COMPANY INFO

LINKED

Z4 CO2 lasers Tube
Category: Gas Laser  Publish Time: 2014-07-10 23:04 

Z4 CO2 lasers Tube
Price : $0.00
Delivery Fee : $0.00
Quantity :
 Part NO. :  DCFBG-series
 Datasheet :  
 Availability :  

Z4 CO2 lasers Tube


Mark & model:Z4, The product is featured as small size and good model,higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.
Origin:Asia and Pacific Area  China
Quality standard:International
H.S.Classification:Machinery & Electronics  Electr.Element  8541 Semiconductor devices; light-emitting diodes etc; parts thereof
Z4 Operation Instruction

Installation Requirement
sure to follow the operation instruction of model Z4 as shown in the illustration. The dedicated power DY13 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv) It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will  be punctured by electricity and may cause water leakage. 

     Operation conditions
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃The operating environment: temperature 2-40℃; humidity 10-60%The working current: test current is 30mA. Maximum working current is 30mA. The running current must be kept below 28mA. The life span can reach 10,000 hours if the current is kept below 26mA.The ammeter must be connected to the negative electrode of laser tube.When it is workingunder over-high current for long term, the negative pole will appear brown yellow, and the life span will be shortened rapidly.To protect dust from going into the insulation sheath, please wrap it with plastic film.
Working Performance
Cutting function.Engraving function: Very good. When the working current is 4mA and the tube is in the  state of preionization, the laser can be used for high-frequency impulse engraving.
Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved,
otherwise the out power will be declined, even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
Safety
The laser beam is invisible light. Please wear protective glasses when debugging the laser.The positive pole is in high voltage. Pay attention to the security marks.
Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environmentis 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way. Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation.The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.
Tubes operated in wrong way are not guaranteed by Manufacturer.
Idealphotonics,Inc
Cardboard Carton  Package Size

DESCRIPBTION

N.W.

G.W.

PACKAGE/UNIT

C.W.

CBM

Laser Tube Z2 (90W)

3.5KG

5KG

1360*250*260

mm

18KG

0.088

Laser Tube Z4 (100W)

4KG

7KG

1550*340*350mm

36.9KG

0.184

Laser Tube Z6 (130W)

5KG

8KG

1800*340*350

mm

43

KG

0.214

Laser Tube Z8 (150W)

6KG

11KG


2010*380*400
mm


62.4

KG

0.304

Laser Tube basic parameter 

Model

Rated power

Max power

length

mm

Φ

mm

Catalyze

Life

span

( h)

Warranty

Z2

90W

100w

1200

80

Yes

10,000

10Months

Z4

100W

130w

1400

80

Yes

10,000

10 Months

Z6

130W

160w

1650

80

Yes

10,000

10 Months

Z8

150W

180w

1850

90

Yes

10,000

10 Months

Related Items


10um series of optical fiber
10um series of optical fiber
10um series of optical fiber
hahshshdhshd